sketch > keycam

HD #16 keycam



a) Felvétel indítása
Bekapcsológombot kb. 5sec nyomni.
Színsorrend: zöld -> piros -> sárga -> maj sárga elkezd villogni (1sec on, 1sec off)

(felvétel közben: sárga 1sec on, 1 sec off, loop
az hogy a zöld led világít, nem kell foglalkozni)

b) sd kártya formázása
1. számítógépre bedug (pendriveként megjelenik)
2. shutter gomb benyomvatart, szgépből kihúz, amikor kialudnak a ledek (10sec?), akkor felenged.

config file

6. It supports audio volume control, and you can even get it mute to save battery and helps to increase the recording time when the audio is not needed, it can be set by TXT config tool.
8. You can set the date and time (white much smaller on the lower left corner), and toggle the date/time stamp on or off, by TXT config tool.
9. Sometimes you may don’t want 720P recording to save battery and memory card capacity, now you can toggle video output frame size from 1280×720 30fps (default), to 848×480 30fps, or 640×480 30fps.
10. Optional AVI output: we also have another firmware option available which will output .AVI file format, using the same H.264 codec, and it offers seamless recording (there is no lost video between clips). If you need it, please send a message to us, and we will send it to you by email.
11. And more. Please find more details in the PDF manual. And of course on RC Forum Tom Frank’s great thread, you will find lots of helpful information there.
#16v2 pros and cons compared to the #16v1.

The Shutter button is the small button all the way to the front.

The Power button is the larger button, right behind the shutter button.

The Reset button is located under the small pinhole situated between the USB connection and the SD card slot. It can be pressed using the end of a paper clip or similar object. Briefly pressing the reset button will force the camera to stop whatever it is doing and turn off.

The other two buttons are dummy. They have no function.

A new, fully charged battery will last about 45 minutes in the keychain model.

You may use any micro SD or micro SDHC card with a capacity of up to 32GB with this camera. To avoid card compatibility problems, always use quality cards with a speed rating of Class 4. Some cards with a faster speed rating may not work properly. The camera only supports cards formatted with FAT32. Cards larger than 32GB, for example micro SDXC will not work with this camera. See below “Breaking the Rules” of how to overcome this limitation.

The camera requires a standard USB cable for charging, connecting to external battery packs
for continuous recording and for connecting to the PC as an external disk or webcam.
All models manufactured in July 2012 and later incorporate a Video-Out function with the
signal output connected to pin #4 on the mini-USB socket. Special cables can be ordered
from the supplier or you can make one yourself.

You must under no circumstances use any other “special” cable, especially the “special”
cable supplied with the #11 (the predecessor to the #16). Doing so will destroy your
camera. So, do not use a #11 “special” cable under any circumstances.

On the original Hardware there was no video-out (composite video).
July 2012 saw the release of V2, a new Hardware design which includes a video-out (TV
composite video) signal. This signal is connected to USB pin #4, the last available pin on the
mini USB socket. Unfortunately, an active video-out signal consumes up to 25% of available
battery power. In order to turn off the video signal using parameter settings, firmware versions
greater than v0.29 are required. For the longest recording times possible, but only if video-out
is not required, the video-out parameter should always be set to “Off”.
Before you start

Before using the camera for the first time, ensure that it is fully charged. See below under “Charging”.
LED status indicators

Since the camera has many functions, it’s important to understand the meaning of the LEDs.

The following LED states are for a camera not connected to the PC.

Yellow LED remains on:
• Camera is in Video recording standby mode.

Yellow LED slowly flashes 15 times and then the camera turns off:
• The memory card is full or not inserted.

Yellow LED constantly slowly flashes (1 sec. On, 1 sec. Off):
• The camera is recording video. The Video Recording indicator (see configuration) must be ON for this to work.

Yellow LED flashing very fast:
• Firmware update in progress. DO NOT press any buttons until all LEDS are off.

Yellow LED flashes quickly 5 times and then the camera turns off:
• This indicates a serious error condition. See Trouble Shooting.

Red LED remains on:
• Camera is in Photo recording standby mode.

Red LED flashes 20 times and then the camera turns off:
• Low battery.

Red LED flashes 3 times and then the camera turns off:
• The camera is turning off, either automatically or manually.
• Note: The camera will only flash while turning off if the Recording Indicator has been configured to be on while recording. The LED will not flash if the Recording Indicator has been configured to be off while recording (secret mode).

Green LED is on:
• The battery is charging. Connecting the camera to the PC

Always connect the camera directly to the PC. Do not use a USB hub.


Connect one end of the supplied standard USB cable to the camera.
Connect the other end to a USB, 5V DC power source (wall charger, PC or external battery).
When charging, the green LED will be on.

When charging is finished, the green LED will be off.

Charging takes about 2.5 hours for a fully discharged battery with the camera turned off and
connected to an external USB Charger. With some batteries the green LED may not turn off
immediately or may even take up to 4.5 hours or longer to turn off. However, it is safe to
assume that after 2.5 hours the battery is fully charged, even if the green LED remains on.
Batteries are not covered under warranty. Charging is limited to around 140mA which offers
the best possible long-term battery protection. If charged with under-rated chargers or using a
USB hub without an additional power supply, expect longer charging times. For optimum
results, the charging voltage should be +5V under load.

Standard formatting tools provided by the operating system are not always reliable. Also, they
do not optimize the SD card’s performance. For optimal card performance it is recommended
to always use the camera’s built-in formatter. Instructions for In-Camera Formatting are
outlined below under “In-Camera Formatting”. Another excellent formatting utility is “SD
Formatter” which can be downloaded from This
utility has been specifically designed for formatting SD cards.
Automatic Power Off from Standby mode

If the camera is in Standby mode (Video mode or Photo Mode) you must take a picture(s) or
start a video recording within *30 seconds. The camera will automatically turn off after *30
seconds of no activity.

*This value can be set using the setup program. Automatic Power Off can also disabled.
If the camera is used for monitoring only, for example fpv, it is imperative to ensure that
Automatic Power Off is disabled in order to prevent signal loss when Standby times out. Turn on Camera
Firmware v0.49 and earlier: Press and hold the Power Button for max. 2 secs. until the Red
LED turns on.

Firmware v0.52 and later: Power-On can be configured as “fast” or “delayed”. In fast mode,
the camera will turn on immediately the Power Button is pressed. In delayed mode, press and
hold the Power Button until the Yellow LED turns on. See additional information below under “Special functions”.

• If the camera has been configured with “Auto Record” set to On, the camera will
automatically begin recording after 4-5 seconds. The yellow LED will blink 3 times
indicating that recording has started. If the camera has been configured to show the
recording indicator while recording, the yellow LED will slowly flash at 2 second
intervals, otherwise the yellow LED will be off.

• If the camera has been configured with “Auto Record” set to Off (default setting), the
camera will switch to video standby mode after about 1 second and the Yellow LED will
turn on.

• If the camera has been configured with “Motion Detect” set to ON, the camera will start
to record as soon as motion is detected. The yellow LED will blink 3 times indicating
that recording has started. If the camera has been configured to show the recording
indicator while recording, the yellow LED will slowly flash at 2 second intervals,
otherwise the yellow LED will be off. If no motion is detected within a given period of
time the camera will return to standby mode and will only start recording again when
further motion is detected. With Firmware v0.52 and above, motion sensitivity
and timeout delay can be configured.

• “Auto Record” and “Motion Detect” are conflicting values. It is not possible to set both
to “on”.
Turn off Camera

Press and hold the Power Button for about 3-5 secs. The red LED may also blink 3 times –
see “LED status indicators”. Note: If the camera is recording, the recording should first be
stopped (see below).
Switching between Video and Photo Standby modes
The camera can be switched between Video Standby and Photo Standby by briefly pressing
the power button. When the camera is in Video Standby, the Yellow LED will be on. When the
camera is in Camera Standby, the Red LED will be on. Recording Video (from Video standby mode, Yellow LED is on)
Start video recording.

• Briefly press the shutter button. The yellow LED will flash 3 times to indicate that
recording has started. If the camera has been configured to show the recording
indicator while recording, the yellow LED will slowly flash at 2 second intervals,
otherwise the yellow LED will be off.
Stop video recording.

• Briefly press the shutter button. The yellow LED flashes twice.
Take a Photo (snapshot) while recording:
• Briefly press the power button to take a picture. The yellow LED will flash twice.
• If Time-Lapse photo has been configured (Firmware v0.47 and above), the camera will
continue to take pictures until the shutter button is pressed. The yellow LED will flash
each time a picture is taken. More information is availyble below under “Special
Taking a Photo (from Photo standby mode, Red LED is on)

• Briefly press the shutter button. The yellow LED flashes twice and then turns back on.
Webcam Mode
• Remove the flash memory card.
• Connect the camera to the PC using a standard USB cable.
• Press the Power Button for max. 2 seconds until the Red LED turns on. The yellow
LED will turn on while initializing the connection to the PC. It will turn off when
connected and the red LED will turn back on indicating a successful connection.
• ► If this is the first time you have connected the camera in WebCam mode, Windows
will automatically install the required drivers.
• The camera is now in Webcam mode.
• Start your favorite WebCam software, such as AMCap. If your screen is black, the
software is not configured correctly. Make sure the program shows the “USB PC
camera” as the “device” selected for video capture. If this option does not show in the
“device” option list, restart the webcam program and check again.
Removable Disk Mode

• Make sure a memory card is inserted.
• Connect the camera to the PC using a standard USB cable. The green LED may turn
on indicating that the battery is charging.
• Press the Power Button for max. 2 seconds until the red LED turns on. The Yellow
LED will turn on while the connection is being initialized and turn of when the camera is
connected. The red LED may remain on or be turned off. The Green LED may also be
on, indicating that the battery is charging.
• The camera is now in Disk Mode and a new removable drive should be available on
your computer. This may take up to 30 seconds.
• ► Note 1: The Red LED will flash during all read/write data transfers with the camera.
• ► Note 2: You may also turn on the camera before connecting to the PC. In-Camera Formatting
The Camera contains a built-in formatter which may be used to format the SD card. Do not
format SDXC cards (cards with a capacity of 64GB and more) see below “Breaking the
Rules”. In-Camera formatting is best done using Nr16Setup.exe (see below) but can also be
done as follows:
• Connect the Camera as a Removable disk (see above).
• Press and hold down the Shutter button. DO NOT RELEASE the button.
• Disconnect the camera from the computer.
• After about 4-6 seconds the camera will turn off (the red LED may also blink 3 times –
see “LED status indicators”), indicating that formatting is completed.
• Release the shutter button.
Camera Setup (Configuration)
On Windows it is recommended to always use the Windows Program Nr16Setup.exe to
modify the camera’s configuration. Nr16Setup.exe will also run on Mac and Linux versions if
Wine is installed. However, it is also possible to manually edit the “SYSCFG.TXT” file which
must be placed in the root folder of the card. You can use any ASCII editor, for example
Notepad, to modify the parameters. The “SYSCFG.TXT” must be in plain ASCII, it must not
be in Unicode. If you don’t know what a root folder is, or you don’t know what ASCII is or don’t
know how to manually edit ASCII files please only use Nr16Setup.exe.
A “SYSCFG.TXT” file can be automatically generated by the Camera and will be placed in the
card’s root directory. The camera’s parameters are self explanatory. It is important not to
change the sequence of the square brackets and not configure invalid combinations. For
example, never combine a clip longer than 5 minutes with the continuous loop. If you enter
invalid combinations or values, the Camera will not perform as expected. It is much safer to
use the setup program which will always configure the camera correctly.
The “SYSCFG.TXT” file can be automatically generated as follows:
1. Disconnect the camera from the PC and turn it off.
2. Press and Hold Down the Shutter button. DO NOT RELEASE the button until
step 6.
3. Press the Power button until the camera YELLOW LED turns on. This will take about
1 second.
4. Release the Power button.
5. Wait until the Yellow LED turns off. This will take about 8-9 seconds.
6. Release the Shutter button.
The camera is updated with the parameters defined in the “SYSCFG.TXT” file by using
exactly the same method as outlined above. Once completed, the “SYSCFG.TXT” file will be
deleted from the card’s root folder.
Using Software to configure the camera
Nr16Setup.exe will automatically configure the camera with the parameters you require.
Detailed instructions can be found in the program by clicking the “Help” button.
All firmware versions from v0.47 enable Nr16Setup.exe to directly communicate with the
camera using the USB connection. Setting parameters using the “SYSCFG.TXT” file is no
longer necessary. Bootloader Update
The bootloader is responsible for correctly loading and updating the firmware. Bootloader V3
and above makes it a little easier to update the firmware, but there are no other advantages.
Installing the bootloader requires the exact same procedure as installing the firmware, which
is described below. The bootloader is installed within a second or two as opposed to up to 12
seconds required to install the firmware.
Firmware Update
Normally, there is no need to update the firmware. You should only update the firmware if you
are having problems with the current firmware or the new firmware provides functionality you
require that are not available in your current version.
The latest firmware version can be downloaded and installed directly from the setup program
or installed manually by downloading the firmware file from

Updating the firmware is an easy and safe process.
If your camera was purchased before November 2012 and has not been updated with
bootloader V3 or greater you will normally need an external card reader (not another #16!) in
order to update the firmware, but there is a “Backdoor” method which is outlined below. Since
all the parameters can be set programmatically using parameters, it is not necessary to load
different firmware versions for different configurations. The only exception is for the video
output format. Because of lack of memory space, different firmware versions exist for AVI and
MOV formats. The AVI format produces non-standard .avi files with a 1 second overlapping
video sequence between clips. The MOV format produces videos which have a 2-3 second
gap between clips.
Manual Firmware Update
Note: Unless the camera is running bootloader V3 or above, the firmware file will NOT be
automatically deleted from the flash card when the camera is turned on. The camera will be
UNUSABLE and reload the firmware file every time it is turned on until a card is used that
has no firmware file on it. This is the reason that you MUST delete the firmware file, after
the update has completed, using an external card reader or the “backdoor” method
described below.
• Copy the new firmware file into the camera’s flash card root folder. This can be done
with the card in the camera connected to the computer as a Removable Drive, or
externally in a card reader. Note: All firmware files are named FWMICDVR.BIN. The
name must not be changed.
• Disconnect the camera from the computer and make sure it is turned off.
• Insert the flash card containing the new firmware file into the camera (if not already in
the camera).
• Press the Power button very briefly until the Yellow LED turns on and begins to flash.
Do not keep it pressed any longer.
• Release the Power Button. The Yellow LED will continue to flash very quickly for a
second or two and then will remain on for up to 12 seconds. It may also blink a few
times. This indicates that the firmware is being written into the camera. DO NOT
PRESS ANY BUTTONS while the yellow led is on or flashing!
• When the firmware is fully installed, the Yellow LED will turn off and the camera will
shut down.
• If the camera is running bootloader V3 or above the camera will automatically restart
and the yellow LED will remain on. The firmware update is complete.
For cameras running an earlier bootloader, continue as follows: • *Remove the card from the camera and insert it into a card reader. You cannot use
another #16 camera for this, but you can use the “Backdoor” method described below.
• Delete the firmware file.
• Remove the card from the card reader and insert it into the camera.
• The camera is now ready for use and has the update firmware loaded.
*Backdoor Method to delete firmware file
If an external card reader is not available, you can delete the firmware file from the card as
• Make sure the camera is turned off.
• Remove the card from the camera.
• Turn on the camera.
• Insert the card back into the camera.
• Connect the camera to the PC using a standard USB cable.
• The camera will now be available as a removable disk.
• Delete the FWMICDVR.BIN from the disk.
• Unplug the camera from the USB.
• The camera is now ready for use and has the update firmware loaded.
Recording using an external power supply
With this camera, it is possible to charge the battery and record at the same time using a
standard external USB 5V DC power supply. The power supply may be mains driven (normal
household wall plug), or run off batteries, including the car charger USB plug (optional
accessory) and cable supplied with the camera.
External USB power supplies usually only use the +5V and the – (Ground/Earth) wires. The 2
data wires are normally not used. However, some USB power supplies designed for a specific
USB device may use different wiring schemes and thus may not work with this camera. To
avoid possible problems, always use a generic power supply.
When turned on, the camera checks for an electric signal on the two Data wires. If a signal is
found, the camera assumes it is connected to a PC and recording will not be possible – see
below “Recording when directly connected to a PC”.
For recording video or taking pictures using a standard external power supply connection, the
USB power supply can be connected at any time, i.e. before the camera is turned on, before
the recording is started, or after the recording has been started.
► If external power is connected and the camera is then turned on, the camera will check the
data lines to determine if it is connected to an external power supply or to a computer.
Because of this, it will take up to 5 seconds until the camera is “ready”, even though the
yellow LED turns on much earlier.
Recording when directly connected to a PC
With this camera, it is possible to charge the battery and record at the same time while
connected to a PC.
In order to record video while the camera is connected to a PC, the video recording must be
started before the camera is connected to the PC. It is not possible to record if the camera is
turned on while connected to a PC. Likewise it is not possible to take pictures while the
camera is connected to the PC. Breaking the Rules
As stated in the introductory, this camera only supports micro SD and micro SDHC Memory
cards. These cards are formatted in FAT32, which is the format the camera requires.
Microsoft has imposed an artificial limit on the maximum capacity of the FAT32 file system of
32GB even though, theoretically, a limit of 2 Terabytes is possible.
Large capacity micro SDXC (XC=Extended Capacity) cards start with a capacity of 64GB. It is
not possible to read these cards with normal SD or SDHC card readers, which includes this
camera. SDXC cards can only be read with special SDXC card readers. SDXC cards placed
in a normal SD(HC) reader may be recognized by the operating system, but will be found to
be unformatted, which is not correct. If formatted using Windows, they will probably be
formatted with 16GB total capacity!
SDXC cards will be recognized correctly if used in an SDXC card reader and the file system
will be exFAT. The maximum capacity of exFAT is 2 Terabytes.
If you use the “In-Camera Formatting” to format your SDXC cards, you do so entirely at
your own risk. The Manufacturer takes no responsibility for incorrectly formatted cards and
the consequences that may arise (for example destroyed cards). SDXC cards formatted with
FAT32 are not supported by Microsoft and you will possibly invalidate your card’s guarantee
by doing so.
Using In-Camera Formatting it is possible to format SDXC cards in FAT32 Format. Doing so
will turn the cards into out-of-specification SDHC cards. However, you will have the
advantage of much higher card capacities. For example, a 64GB SDXC card formatted with
FAT32 will give you about 20 hours of continuous video when recorded with a data rate of 7
Mb/s. After formatting with FAT32 these cards will be recognized by Windows using normal
SD(HC) card readers, which includes this camera, to their full capacity. Note that the max. file
size of 4GB still applies.
SDXC cards formatted with FAT32 may be converted back to exFAT by using SDFormatter
but an SDXC card reader must be used.
Special functions
The following functions need additional explanation:
Power-on Delay
This parameter was added in v0.50 and gives the user the choice of the existing 2-3 sec.
delayed power-up, or an instantaneous power-up with no delay. Note that the system requires
about 2 seconds after power-on until the buttons become active.
Audio Volume
As of v0.67, when the volume is turned OFF, the sound track is completely eliminated from
the video output stream in all camera modes. Prior to this version a sound track was attached
to the video but with the volume turned off. The new functionality will free up a nominal
7% video recording space when the volume is turned off. Motion detection
Motion detection was introduced in v0.49 and additional parameters for adjusting the
sensitivity and timeout were introduced in v0.58. If motion detection is enabled, Auto Record,
Auto-shutoff, Time-lapse Photos and TV Video-Out must be disabled. Motion detection starts
automatically after a 5 sec. delay after the camera is powered on. During the delay period, the
camera can be:
• Toggled into normal video mode by pressing the shutter button. The camera will revert
back to normal Motion Detect mode when normal video is stopped with Shutter Button.
• Toggled to Photo Mode with the power button.
• Placed into position to prevent the motion from turning on the camera and starting the
first motion-triggered clip.
Recording will continue as long as there is movement detected. If no more movement is
detected, the camera will enter a timeout loop and check for more motion. If no new motion is
detected during the timeout loop the camera will stop recording and wait for further movement
when it will start recording again. This procedure will be repeated ad infinitum.
Once motion is detected, it will take a second or two until the firmware starts recording. This
delay can’t be avoided because of technical limitations.
Time Lapse
Time Lapse was introduced in v0.43 and further refined in v0.50. If Time Lapse is enabled,
Auto Record and Motion detect must be disabled. Photo delay settings also include 0.50 and
0.25 secs. If these two low settings are used, Photo Frame size must be set to 1280×720 and
the Time stamp must be disabled. The Auto-shutdown setting can remain active with Time
lapse turned on because it will only function when the camera is toggled out of photo mode
back into standby mode. The 0.25 sec. delay between images, when joined into a movie at
30 fps, will equate to a 7.5x time lapse speed up.
Video Frame Rate
This parameter was added in v0.50 and allows recording video with frames rates of 5, 10, 15,
20, 25, or 30 fps. These can give additional time lapse video modes::
• The 5 fps mode is special, and will automatically play back at 30 fps. This means the
NATIVE video in this mode will give a 6X speed-up with NO editing!
• The other frame rates play back at the same frame rate as the capture rate (e.g., 10
fps capture will play back at 10 fps – no speed up, but jerky motion).
Editing the special frame rates to play back faster can produce slower “time lapse” motion
than the Time-lapse Photo settings, e.g.:
• 5 fps video at 30 fps = 6x speed up
• 10 fps video at 30 fps = 3x speed up
• 15 fps video at 30 fps = 2x speed up
• 20 fps video at 30 fps = 1.5x speed up
• The 25 fps mode is currently not available due to incompatibility with new library code
from the chip vendor. When a fix id released it will be added. If this value is set, 30fps
will be used instead. Trouble shooting
Q. The camera is not recognized as a removable disk or as a Webcam.
A. The operating system must be XP or greater. The camera must be connected using a
standard USB cable. Confirm that the cable is not defective by attaching another USB device
using the same cable. Do not use a USB hub. Try using another USB port. Defective cables
are the most common problems when the camera is not correctly recognized by the PC.
Q. The yellow LED flashes once per second 15 times and then turns off.
A. There is no micro SD card inserted, the card is not properly inserted, the card is full or the
card is defective. The card must be inserted with the gold contacts facing upwards, towards
the buttons. There should be a distinct spring action when inserting the last 5 mm and there
should be no friction whatsoever.
When the card is pushed 1 mm inside the body the card should latch with a distinctive click.
Never force the card, and never push the card more than max. 1 mm into the camera body.
Sometimes the card holder metal frame is not positioned properly in the body and is clearly
visible in the card slot. If this is the case, insert the card above (on the button side) of the
visible metal frame.
Q1. After I turn the camera on it immediately turns off (the red LED may also blink 3 times –
see “LED status indicators”).
Q2. When I press the shutter button to take a picture or make a video, the camera reacts
normally, but after about 30 seconds the camera turns off (the red LED may also blink 3 times
– see “LED status indicators”).
Q3. When I press the shutter button to take a picture, the red LED is on as normal, but I can
also see the yellow LED flashing at the same time. After about 30 seconds the camera turns
off (the red LED may also blink 3 times – see “LED status indicators”).
A. This indicates that the SD card is full or data on the SD card is not as expected. Maybe the
card was previously used in another device. Format the card and try again. If this fails, try
another card.
Q. The camera does not react. The green LED may be on or off.
A. The firmware may have entered a continuous loop, or the battery may be discharged.
• Make sure the battery is fully charged.
• Use a paper clip or similar object to press the Reset button. This should force the
camera to be turned off.
• Wait 10 seconds.
• Turn on the camera.
• As a last resort, disconnect the battery and reconnect again after waiting 30 seconds. Q. With or without an inserted card, the yellow LED flashes 5 times fairly quickly (about once
every 1/4 second) and then turns off.
A. This can happen when a firmware file is not updated correctly. The camera will also no
longer react to button presses.
• Remove the card from the camera and use a paper clip or similar instrument to briefly
press the reset button. The camera will most probably flash 5 times.
• Using a card reader or another camera connected as a removable device, copy a
known good firmware file (FWMICDVR.BIN) to the card.
• Insert the card into the defective camera. DO NOT turn it on.
• Briefly press the reset button.
• The yellow LED should flash quickly for a few seconds while the firmware is updated.
• Remove the card and, using an external card reader or the “Backdoor” method, delete
the firmware file (see Firmware Update).
Q. Playback is erratic or stutters or the playback colors are psychedelic or the video flashes,
has corrupted blocks etc.
A. Always first copy the video file from the memory card to your hard drive.
• Your PC or graphics card may not be powerful enough to playback the video stream.
• You may not have enough memory installed in your PC.
• Use VLC Media Player. Window Media Player often chokes on underpowered
• Psychedelic colors may also indicate problems with the CMOS lens module. Make
sure the CMOS lens cable is correctly seated and not cracked. The lens cable is very
Q. When I turn on the camera the yellow LED tuns on but the I can’t take a video or photo.
The shutter button doesn’t react.
A. .Most likely you have dropped the camera and the ribbon cable which connects the lens
assembly to the circuit board has become dislodged. You will have to open the camera,
remove the battery and very carefully reseat the ribbon cable. Instructions on how to remove
the lens assembly can be found in the simple instruction manual pdf file which was supplied
with the camera.
Getting Help
This camera is the best supported camera of it’s kind. In case of problems or questions your
first stop should be a visit to:

This thread is dedicated to questions related to the #16 camera. It should be noted that the
forum is for aerial RC discussions only, so please avoid post anything off-topic. The first 5
posts contain links to all the important information, including a list of sources where you can
buy this camera. ONLY buy from the sources listed. It is very probable that other sources will
offer fake copies. These copies are NOT original and will NOT perform as expected.
This entry was posted in Electronics and tagged 808. Bookmark the permalink.
Post navigation
← How to choose battery for Quadcopter, Tricopter and Hexacopter
LC Filter and FPV →
4 thoughts on “How to Use 808 #16 Key Chain Camera Manual and Wiki”

saverio says:
December 24, 2014 at 11:05 am

ciaooooo ..e’ possibile ricevere un formato avi supplementare per la mia 808 car keys micro camera???? GRAZIE!!!!!
Merri says:
July 4, 2014 at 3:44 am

you’re truly a good webmaster. The site loading pace is
amazing. It sort of feels that you’re doing any distinctive trick.
In addition, The contents are masterwork. you have performed a great activity in this topic!
Stefan says:
September 8, 2014 at 7:11 pm

I’m really еnjoying thе theme/design of your site.
Do you ever гun into any browser compatibility prοblems?
A number of my blog visitors have complained about my blog
not wοrking correctly in Explorer but looks great in Fіrefox.

Do you have any tips to help fix this issue?
Tristan says:
September 26, 2014 at 2:04 am

You are so awesome! I don’t suppose I’ve truly read a single thing like
that before. So great to discover another person with unique thoughts on this topic.
Seriously.. thank you for starting this up. This website is something that is required on the
web, someone with some originality!

Unless otherwise stated, the content of this page is licensed under Creative Commons Attribution-NonCommercial-NoDerivs 3.0 License