First competition

community

The goal of this competition

Having a good enough slic3r configuration file for everyone who uses arcol.hu hotend v4.x with hyena hobbed bar.

My reference entry (arcol.hu)

flickr:8628296823

This is the Voronoi cat, thing:45012 processed with slic3r 0.9.9..

Printed with black ABS, slic3r 0.9.9, with a 0.35mm nozzle.
The printed modell is 80mm high and no cleanup at all.
Also no support is used, and printed with single head.

Get the config.ini at the bottom of this page.

Olle's entry

flickr:8628419793

Printed with slic3r 0.9.9. with 0.35mm nozzle by Olle.

Get the config.ini at the bottom of this page.

Kyle's entry

flickr:8629583084
flickr:8628461885

Simply Twisted; thing:29019 processed with slic3r 0.9.9.

Printed with slic3r 0.9.9, from natural PLA with a 0.5 nozzle (v4.2hotend).
The model is 39mm high and no cleanup. A hyena v2 was used.

Get the config.ini at the bottom of this page.

Voronoi cat's config.ini

This config.ini was exported from slic3r 0.9.9

# generated by Slic3r 0.9.9 on Sun Apr  7 17:25:22 2013
avoid_crossing_perimeters = 
bed_size = 185,164
bed_temperature = 120
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 60
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 0
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 1
fan_below_layer_time = 25
filament_diameter = 2.82
fill_angle = 45
fill_density = 0.25
fill_pattern = rectilinear
first_layer_bed_temperature = 115
first_layer_extrusion_width = 0.5
first_layer_height = 0.3
first_layer_speed = 75%
first_layer_temperature = 260
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 75
layer_gcode = 
layer_height = 0.21
max_fan_speed = 40
min_fan_speed = 25
min_print_speed = 10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.35
only_retract_when_crossing_perimeters = 1
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.4
perimeter_speed = 51
perimeters = 3
post_process = 
print_center = 92.5,82
raft_layers = 0
randomize_start = 0
resolution = 0
retract_before_travel = 5
retract_layer_change = 1
retract_length = 0.5
retract_length_toolchange = 10
retract_lift = 0.21
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 10
rotate = 0
scale = 1
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 10
small_perimeter_speed = 50%
solid_fill_pattern = rectilinear
solid_infill_below_area = 20
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 80%
start_gcode = G28 ; home all axes
support_material = 1
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.4
support_material_interface_layers = 2
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 45
support_material_threshold = 60
temperature = 252
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 60%
top_solid_layers = 3
travel_speed = 85
use_relative_e_distances = 0
vibration_limit = 0
z_offset = -0.12

Olle's config.ini

# generated by Slic3r 0.9.9 on Sun Apr  7 13:38:45 2013
avoid_crossing_perimeters = 0
bed_size = 180,165
bed_temperature = 110
bottom_solid_layers = 2
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
cooling = 0
default_acceleration = 0
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors
external_perimeter_speed = 100%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_diameter = 2.9
fill_angle = 45
fill_density = 0.15
fill_pattern = honeycomb
first_layer_bed_temperature = 110
first_layer_extrusion_width = 150%
first_layer_height = 80%
first_layer_speed = 60%
first_layer_temperature = 235
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
layer_gcode = 
layer_height = 0.25
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.35
only_retract_when_crossing_perimeters = 0
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 45
perimeters = 2
post_process = 
print_center = 90,85
raft_layers = 0
randomize_start = 1
resolution = 0
retract_before_travel = 0.2
retract_layer_change = 1
retract_length = 0.5
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
rotate = 0
scale = 1
skirt_distance = 6
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 15
small_perimeter_speed = 30
solid_fill_pattern = concentric
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 70
start_gcode = G28 ; home all axes
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 45
temperature = 235
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 2
travel_speed = 130
use_relative_e_distances = 0
vibration_limit = 0
z_offset = -0.0

Kyle's config.ini

# generated by Slic3r 0.9.9-dev on Fri Mar 29 18:10:37 2013
avoid_crossing_perimeters = 0
bed_size = 140,170
bed_temperature = 0
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 58
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 1
duplicate = 1
duplicate_distance = 6
duplicate_grid = 1,1
end_gcode = M104 S0 ; turn off temperature\nG0 X0 Y0\nM106 S255\nM84     ; disable motors
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0.66
fan_always_on = 1
fan_below_layer_time = 60
filament_diameter = 2.8
fill_angle = 45
fill_density = 0.3
fill_pattern = rectilinear
first_layer_bed_temperature = 0
first_layer_extrusion_width = 235%
first_layer_height = 200%
first_layer_speed = 18%
first_layer_temperature = 185
g0 = 0
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.55
infill_first = 0
infill_only_where_needed = 0
infill_speed = 60
layer_gcode = 
layer_height = 0.1
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.5
only_retract_when_crossing_perimeters = 1
output_filename_format = [input_filename_base].gcode
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.55
perimeter_speed = 30
perimeters = 1
post_process = 
print_center = 70,85
raft_layers = 0
randomize_start = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 30
rotate = 0
scale = 1
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 30
small_perimeter_speed = 30
solid_fill_pattern = rectilinear
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extrusion_width = 0
solid_infill_speed = 60
start_gcode = G0 X0 Y0 Z0\nG92 E0
support_material = 0
support_material_angle = 0
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
temperature = 180
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 50
top_solid_layers = 3
travel_speed = 130
use_relative_e_distances = 0
vibration_limit = 0
z_offset = 0
Unless otherwise stated, the content of this page is licensed under Creative Commons Attribution-NonCommercial-NoDerivs 3.0 License